GOOD TO KNOW ABOUT THE TILE-ABLE DRAIN. You can flip the tile-able channel and enjoy the smooth steel cover, instead of the tile-able one. Channel width measured outside: 70mm. Width of the tile tray measured inside: 50mm.
[additionally 20mm each side for the peripheral edges underneath]. Height of the tile edge inside the tray: 12mm - applies to the tile-able model ONLY. Height of the installation ONLY 52mm = ULTRAFLAT.
Does not require a deep cut to install - low installation height - works well even if the slab isn't very thick. For more detailed measurements - see the drawing in the photo gallery. The drain is made of stainless steel AISI 304 1.2mm thick with nickel content at least 8%.
Fine, clean weld seams - fully welded - not spot welded. Siphon made of stainless steel with removable debris collector/fluff filter allowing easy cleaning with access from the top. It also blocks bad odours/smells from the drains and acts as a shield against loosing small jewellery like rings, earrings etc. = the trap is included. Use the grey plastic connector to connect this drain to the 50mm pipe (connector is included in the set).It needs to be pushed onto the steel end of the drain and the other end pushed into the 50mm pipe (push fit). If your pipes are 40mm diameter, there is no need to use the plastic connector as the steel outlet of the drain is 40mm diameter. All our drains come with 10 years guarantee. If you require more quantities than available on the listing - get in touch.
And we will make more pieces of the specific drain available for you (and a discount too). 1 x stainless steel drain channel. 1 x removable debris collector. 1 x removable protecting sieve. 2 x adjustable and removable feet.1 x sealing waterproof cloth. 1 x plastic connector/adaptor for 50mm pipe.
1 x metal hook for lifting the tile tray. 1 x stainless steel patterned cover - only with drains with patterned grate. 1 x stainless steel tile tray - only with tile-able drains. Or call: 01403 711820 or 7494 226600.Feedback after receipt of your order would be very much appreciated - THANK YOU. Make sure to leave 10cm on each side for a comfortable installation (unless you work with a very skilled installer/tiler - than it can be 5cm on each side). For a less visible effect - so the linear drain'melts onto' the floor - choose the tile-able model. If you want the installation done quicker and easier and you like one of our stainless steel cover designs, then go with the covered drain and avoid having to cut the tiles. For installation of our product, for the best results, use a polymer glue for joining the grey plastic connector with a pipe (if you need to use it at all) and then seal it with a cement solvent polymer glue, like: Flex, High Tack, FixALL, etc. Should you need an invoice with VAT stated separately, please get in touch or add a note to your order at the check-out. For standard post of 1st Class you should allow between 1-3 days despite the estimated date. Every listing has various postal options from Signed for, Tracked 24H courier or Next Day by 10:30 (at additional cost if needed) for your convenience. You will have to cover the cost of posting the product back to us.
Any product you return must be in the same condition you received it and in the original packaging with all labels that it came with. Any claims for short deliveries, damaged goods or incorrect items must be advised within 3 days of the receipt of goods.
Under no circumstances we will be liable for any loss, damages or remedial expenses whether or consequently arising from the goods supplied for any purpose. Please be aware it is your responsibility to check the product detail and item specifics where the information is provided. If in doubt please get in touch befroe placing the order. While we endavour to ensure that the product info and specs are correct, we do not warrant the accuracy of the material on the listings.Producer specs can alter at any time and we endavour to note these changes but cannot be held responsible for alterations beyond our control. Stainless Steel LINEAR FLOOR SHOWER DRAIN Length range: 30cm, 40cm, 50cm, 55cm, 60cm, 65cm, 70cm, 75cm 80cm, 85cm, 90cm, 95cm, 100cm, 110cm, 120cm GOOD TO KNOW ABOUT THE TILE-ABLE DRAIN: you can flip the tile-able channel and enjoy the smooth steel cover, instead of the tile-able one Measurements: Channel width measured outside: 70mm Width of the tile tray measured inside: 50mm [additionally 20mm each side for the peripheral edges underneath] Height of the tile edge inside the tray: 12mm - applies to the tile-able model ONLY Height of the installation ONLY 52mm = ULTRAFLAT Does not require a deep cut to install - low installation height - works well even if the slab isn't very thick For more detailed measurements - see the drawing in the photo gallery. Materials and main features The drain is made of stainless steel AISI 304 1.2mm thick with nickel content at least 8%. = the trap is included Use the grey plastic connector to connect this drain to the 50mm pipe (connector is included in the set). This item is in the category "Home, Furniture & DIY\Bath\Shower & Bath Accessories\Other Shower & Bath Accessories". The seller is "etradebathrooms" and is located in this country: GB. This item can be shipped worldwide.